Chemical-free mold removal that leaves your framing dry

Dry Ice Blasting Mold in WEST HILLS, California

Dry Ice Blasting Mold in WEST HILLS, California is the fastest way to strip mold off raw wood, brick and ductwork without soaking your house. Our IICRC-trained crews blast at -109°F, lift the growth off the surface, and HEPA-vacuum the debris the same visit. If you have found black mold infestation behind drywall or in a crawl space, call (833) 929-5837 and we will be there today.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service West Hills
Careful work. Honest options.
About this service

What Dry Ice Blasting Mold in WEST HILLS, California Does

Dry Ice Blasting Mold in WEST HILLS, California is a dry remediation method that fires rice-sized pellets of solid carbon dioxide at roughly 300 PSI. The pellets hit the mold at -109°F, freeze it, and the kinetic impact lifts it off the substrate. Because the CO2 sublimates on contact, there is no water, no sand, and no chemical residue left behind. We use it on exposed framing, joists, subfloor, brick, concrete, and metal ductwork where wet cleaning would just feed the problem.

Most WEST HILLS homes we walk into have the same story: a slow supply-line leak behind a bathroom vanity, a roof flashing failure from last winter's storms, or a crawl space that never dried out after the 2023 rains. By the time you smell that musty odor, the mold has been growing for weeks. Dry ice mold removal WEST HILLS crews perform is the only method that cleans the surface and leaves the wood dry enough to close back up the same day.

  • ✓ No Water, No Regrowth
  • ✓ Reach Tight Framing Cavities
  • ✓ No Sand or Soda Cleanup
  • ✓ Protects Wiring and Ductwork
What's included

What Our Dry Ice Blasting Mold Service Includes

Every dry ice blasting mold job includes the full chain from inspection through clearance testing. We do not sell the blasting as a standalone service because blasting without containment and verification is how mold comes back. Here is what is covered in a standard scope.

✓

On-Site Inspection and Scope

A technician walks the property with a moisture meter and thermal imaging camera, documents affected areas with photos, and writes a scope with square footage and substrate types. You get the written scope before any work begins.

✓

Full Containment Setup

We seal the work zone with 6-mil plastic sheeting and run a negative air machine with HEPA filters. This keeps spores from migrating into living areas during blasting. Setup and teardown are included in the price.

✓

Dry Ice Blasting of Affected Surfaces

We blast every accessible mold-affected surface, including the back side of sheathing and the gaps between studs. Pellet feed rate and pressure are adjusted per substrate so we clean without gouging the wood.

✓

HEPA Vacuum and Antimicrobial Treatment

After blasting, we HEPA vacuum all horizontal surfaces and apply an antimicrobial coating to the cleaned substrate. We use Fiberlock ShockWave or Concrobium depending on the material and the mold species present.

✓

Fogging for Airborne Spores

A Benefect fogging pass handles airborne spores and residual odor. This is the step that makes the difference between a job that smells clean and one that still smells musty a week later.

✓

Post-Remediation Clearance Testing

We collect air and surface samples and send them to an independent lab. You get the written report in 24-48 hours. If clearance fails, we re-blast the affected area at no additional charge.

How it works

Our Dry Ice Blasting Mold Process

01

Inspection and Mapping

We start with a moisture meter and a thermal imaging camera to find every wet zone, not just the visible mold. A borescope camera goes into wall cavities and behind baseboards. You get a written scope with photos and moisture readings, usually within 90 minutes of arrival.

02

Containment Setup

We seal the work area with 6-mil plastic sheeting and run a negative air machine with HEPA filters so spores cannot migrate into the rest of your house. Every technician suits up in personal protective equipment. Setup takes 30-45 minutes on a typical 200-square-foot remediation.

03

Dry Ice Blasting

The dry ice blasting machine runs at 250-300 PSI with a pellet feed rate tuned to the substrate. Softwood framing gets a lighter pass, brick and concrete get a heavier one. A single technician covers roughly 100-150 square feet per hour depending on how deep the growth has gone.

04

HEPA Vacuum and Antimicrobial

Once the mold is off, we HEPA vacuum every horizontal surface and apply an antimicrobial coating. We use products like Fiberlock ShockWave or Concrobium depending on the substrate. Fogging with Benefect handles the airborne spores and the musty odor at the same time.

05

Post-Remediation Testing

We take air samples and surface samples and send them to a third-party lab. You get the report in 24-48 hours. If clearance fails, we re-blast the affected area at no additional charge. Most WEST HILLS jobs clear on the first pass.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry Ice Blasting Machine

Fires rice-sized CO2 pellets at 250-300 PSI to freeze and lift mold off wood, brick, concrete, and metal without water or abrasive media.

Thermal Imaging Camera

Finds hidden moisture behind walls and under floors before we open anything up. It is how we locate the source, not just the visible growth.

Moisture Meter

Confirms moisture content in framing and subfloor. We use it to verify the substrate is dry enough to close back up after blasting.

Borescope Camera

Lets us see inside wall cavities and duct interiors without cutting large access holes. It documents the scope with photos for your records and your insurer.

HEPA Vacuum and Air Scrubber

Captures mold spores and debris during and after blasting. The air scrubber runs continuously to keep the work zone under negative pressure.

Negative Air Machine

Maintains negative pressure inside the containment so spores cannot migrate into the rest of the house while we are working.

Fogger

Applies Benefect or a similar antimicrobial as a fine mist to reach airborne spores and surfaces the blaster cannot touch.

Real results

Before and after.

Bathroom Vanity Leak, West Hills

Before

A slow supply-line leak under the bathroom sink had been soaking the cabinet base and the wall cavity for an estimated six weeks. Visible black mold covered roughly 12 square feet of drywall and the adjacent studs. Moisture meter readings on the framing were above 28%.

After

We removed the affected drywall, blasted the framing and sheathing with dry ice, and applied Fiberlock ShockWave. Post-blast moisture readings dropped to 9-11%. Third-party clearance testing came back clean on the first pass, and the wall was closed up two days later.

Crawl Space Mold, Canoga Park

Before

A 900-square-foot crawl space had visible mold growth on roughly 60% of the floor joists and subfloor. The musty odor was noticeable in the living room above. A borescope inspection found the moisture source was a slow drain leak combined with poor ground drainage.

After

We contained the crawl space, blasted all affected joists and subfloor, HEPA vacuumed, and fogged with Benefect. Clearance testing confirmed spore counts back to outdoor baseline. The homeowner installed a vapor barrier afterward to keep the space dry.

HVAC Duct Mold, Woodland Hills

Before

A four-unit apartment building had musty odors in two units. Inspection with a borescope found mold growth inside roughly 40 feet of sheet-metal supply trunk line. Air quality testing showed indoor spore counts at three times the outdoor baseline.

After

We blasted the duct interiors with dry ice, HEPA vacuumed the system, and ran an antimicrobial fogging pass. Post-remediation air testing showed spore counts back to normal. Total job time was two days across both units.

Problems we solve

Mold Problems We Solve With Dry Ice Blasting

Most West Hills mold jobs trace back to one of a handful of moisture sources. Here are the ones we see most often and how dry ice blasting solves them without tearing the house apart.

Ask a pro →
01

Black mold infestation behind bathroom walls

We contain the bathroom, remove the affected drywall, and dry ice blast the framing and back side of the sheathing. Antimicrobial coating goes on after, and clearance testing confirms the space is safe before we close it up.

↗
02

Crawl space mold from chronic ground moisture

Dry ice blasting cleans joists, subfloor, and piers without adding water to a space that already struggles to dry. We follow with an antimicrobial coating and can recommend encapsulation materials to stop the moisture from coming back.

↗
03

Attic mold from roof leaks and poor ventilation

We blast the sheathing and rafters with dry ice, which cleans the surface without introducing moisture into an already humid attic. Insulation that is contaminated gets removed and replaced; the structural wood gets saved.

↗
04

HVAC mold contamination in ductwork

Dry ice blasting cleans the interior of sheet-metal ductwork in place, which no wet method can do safely. We HEPA vacuum the system afterward and treat with an antimicrobial fogging pass.

↗
Proof you can check

Licensed, Certified, and Verified

✓
IICRC CertificationInstitute of Inspection, Cleaning and Restoration Certification
✓
ACAC CertificationAmerican Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
OSHA Safety TrainingOccupational Safety and Health Administration
✓
California Contractor LicenseCalifornia Contractors State License Board
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs run $1,800 to $4,500 in 2026, depending on square footage and how deep the growth has gone. A single bathroom cavity might land near the low end; a full crawl space with ductwork can push past $6,000. Inspection and post-remediation testing are usually bundled into the quote. Call (833) 929-5837 for a written number.

Yes. The CO2 pellets sublimate into gas and leave no residue, so there is nothing toxic left on the framing. We still run negative air with HEPA filters and wear full personal protective equipment because the mold spores themselves are the hazard, not the blasting media. Occupants can usually stay in the home if the containment is sealed properly.

We blast exposed wood framing, plywood sheathing, OSB, brick, concrete, cinder block, sheet metal ductwork, and most electrical components. It is not the right method for drywall, insulation, or anything already soft from water damage. Those materials get removed and replaced. During inspection we tell you exactly which surfaces can be saved.

It removes the mold and its food source from the surface, which is what matters. The blasting itself does not sterilize the substrate, so we follow every pass with an antimicrobial coating like Fiberlock ShockWave or Concrobium. That combination is what passes third-party clearance testing. Killing spores without removing the growth just leaves dead mold behind.

Ready when you are

Get Dry Ice Blasting Mold in WEST HILLS, California Today

Every day you wait, the mold spreads further into the framing. Call (833) 929-5837 and we will schedule an inspection, give you a written scope, and start dry ice blasting as soon as you approve. Licensed, insured, and cleared by third-party testing on every job.

Book Inspection (833) 929-5837 →
Request an appointment

Contact Our West Hills Mold Team

Call us at (833) 929-5837 or send an email to schedule your free mold inspection. We answer the phone 24/7 for emergency calls and return non-urgent messages within one business day. Our office is in West Hills, California, and we serve the surrounding communities including Bell Canyon, Hidden Hills, Woodland Hills, Canoga Park, and Northridge.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837